Scosche-industries IBHPK User Manual download pdf (Page 2)

NOTE: Will also charge your iPod until transmitter charge is full.

Before using this for the first time, charge the headphones and transmitter for a full 2.5 hours.

A cable is provided in the kit for charging.

1. Plug the Mini cable end of the charger cord into the charging jack as shown in Illustration 2.

2. Connect USB Cable to an available PC/Laptop USB port or 110v AC USB wall adapter/

power supply. (AC adapter not included).

3. Charge Battery for 2.5 hours (LED will illuminate RED when charging).

4. The RED LED will turn off when charging is complete. Unplug each device and enjoy up to

5 hours of use.

5. Purchase wall and car adapters to charge at home and/or on the road.

(IPPWR / IP2IN1 - Sold Separately)

GENERAL PAIRING NOTES:

1. Keep the Bluetooth® products within a distance of 3 ft. ( 1 meter) when pairing.

2. These products are designed for AUTO-pairing function and no user input should be

required. If for any reason you are asked for a passcode by any Bluetooth® device,

always use "0000".

3. As a general rule, power the receiving device FIRST before the transmitting device.

(Headphone is the receiver)

4. Compatible devices must be Bluetooth® v1.2 supporting A2DP profile.

5.Turn off any other nearby Bluetooth® devices, such as a cell phone or headset as this

may hinder pairing process between your devices.

6.Pairing can take up to 1 minute, sometimes more. Once initial pairing is complete between

your headphones, transmitter and Bluetooth® phone, reconnecting during normal use

occurs in a fraction of the time.

PAIRING UBHP HEADPHONES TO THE IPBTT TRANSMITTER:

1. Press the Power Button on the UBHP headphones for 3 seconds. Blue LED will flash indicating pairing

mode.

2. Press the power Button on the IPBTT transmitter for 3 seconds. Blue LED will flash quickly indicating

pairing mode.

3. Pairing should occur within 1 minute but can take up to 5 minutes. Blue LED will stop flashing on the

headphones and flash slowly on the transmitter.

4. Plug the transmitter into your iPod bottom dock. You should hear the audio through your Bluetooth®

Headphones.

5. If you are successful pairing the devices, repeat steps 1-4 above. Make sure receiving device is powered

first as suggested in pairing notes and power off any other Bluetooth® mobile devices. If you still cannot

successfully pair the devices, go to the TROUBLESHOOTING steps i this manual or call Tech Support

at (800) 621-3695 Ext.3

CHARGING

NOT TO SCALE

WALL ADAPTER

(NOT INCLUDED)

WALL OUTLET

USB

CABLE

ILLUSTRATION 2

CHARGING CONNECTIONS

SCOSCHE UBHP

HEADPHONES

OPTIONAL

PAIRING

PAIRING UBHP HEADPHONES TO A BLUETOOTH® CELL PHONE:

1. Place headphones and Bluetooth cell phone with in 3 ft. (1m) of each other.

2. Ensure headphone power is off.

3. Press the power button on the right earpiece for 3 seconds. The Blue LED will flash indicating pairing mode.

4. While the headphone LED is flashing Blue, follow the instructions for your cell phone to seek (or discover)

any Bluetooth® devices. You will be pairing the Scosche Bluetooth® headphones to your phone just like you

would pair any Bluetooth® handset or hands-free kit. If needed, consult your cell phone's manual for

information on pairing or discovering Bluetooth® devices for your particular phone.

5. Your cell phone should display a list of local Bluetooth® devices. The Scosche headphones should be

displayed as a device named "SCOSCHE" Headphones.

6. Select this device and your cell phone should connect to this device automatically. If your phone happens

to ask for a password (or passcode) then enter "0000".

7. Bluetooth® pairing should now be complete. (Blue LED on solid) If your phone fails to locate the Scosche

headphones, then check to make sure your phone is seeking Bluetooth® devices. Check to make sure the

Scosche headphone power is switched ON and the LED light is flashing Blue indicating "pairing" mode.

Repeat steps 1-6 if you cannot successfully pair the two devices, or go to the TROUBLESHOOTING steps

in this manual or call Tech Support at (800) 621-3695 Ext.3.

8. Place the headphones over your ears and make a test call from your cell phone. Your cell phone audio

should be heard through the headphones.

PAIRING CONTINUED

HEADPHONE & TRANSMITTER OPERATION

POWER ON/OFF NOTE:

Under normal use, we suggest powering on the headphones (receiver) first, then power on your Bluetooth®

transmitter. This method will produce the shortest connection time between the devices. if using a

Bluetooth® cell phone, then connect to the headphone AFTER the transmitter is connected as the third

device in your group. If you have previously paired with your Bluetooth® cell phone, then select the Scosche

headphones from the Bluetooth® device list and choose to connect.

POWER ON OFF: Press the Power Button for 3 seconds to turn the transmitter ON or OFF

CONNECTION

Connect IPBTT to the bottom dock of your iPod. Turn the IPBTT on, then turn on your

Bluetooth® headphones or receiving device. Once the two devices are paired, enjoy the audio.

REMOTE CONTROL SOURCE FUNCTIONS

ONLY when used with device that support the AVCRP profile for remote

control functions. ( Scosche Bluetooth® headphones - UBHP)

- PLAY/PAUSE

Press the power button on your Bluetooth® headphones (or other receiving devices)

to PLAY or PAUSE the current track. Do not hold down the power button for

for more than 1 second or it may turn off the power.

(NOTE: Volume control will no longer be controlled through iPod wheel, only

through Bluetooth® device controls).

- TRACK UP/DOWN

1. Press and hold the volume up button to skip forward to the next track.

2. Press and hold the volume down button to skip back to the beginning of the song.

3. To track to previous song press and hold immediately after step (2).

CELLULAR OPERATION

INCOMING CALL ANSWER:

With your UBHP headphones powered and a Bluetooth

wireless link established, a ring tone will be heard

inside the headphones when you receive an incoming phone call. Simply press and release the Power

Button to ANSWER an incoming call. If you were listening to music at the time, it will be interrupted during

your call. You will hear the other party through the left headphone speaker and they will hear you through

the built-in microphone on the right earpiece. The audio will return when the call ends.

ENDING A CALL:

When you are finished with the call, simply press and release the Power Button to END the call.

CELLULAR RE-CONNECTING:

Once you have initially paired your cell phone with the UBHP Bluetooth

headphones, operating steps may

vary when needing to re-establish a Bluetooth

link between the headphones and cell phone. Some

phones may attempt to reconnect automatically as soon as they "see" the UBHP and some phones may

require you to select the "Scosche" headphones from a list of cataloged Bluetooth

devices in your

particular phones memory. If needed, consult your cell phone’s manual for information on connecting to

Bluetooth

devices for your particular phone.

IPBTT Transmitter

1 2 3

Comments to this Manuals

No comments

Scosche-industries IBHPK User Manual Page 2

Comments to this Manuals